-
1 functional test equipment
Military: FTEУниверсальный русско-английский словарь > functional test equipment
-
2 аппаратура для проверки работоспособности
Quality control: functional test equipmentУниверсальный русско-английский словарь > аппаратура для проверки работоспособности
-
3 аппаратура для функциональных испытаний
Quality control: functional test equipmentУниверсальный русско-английский словарь > аппаратура для функциональных испытаний
-
4 оборудование для проверки работоспособности
Quality control: functional test equipmentУниверсальный русско-английский словарь > оборудование для проверки работоспособности
-
5 оборудование для функциональных испытаний
Military: functional test equipmentУниверсальный русско-английский словарь > оборудование для функциональных испытаний
-
6 испытание
test
- амортизации шасси, динамическое (копровое) — landing gear drop test
- в аэродинамической трубе — wind tunnel test
- в барокамере — altitude chamber test
- в гидроканале — tawing basin test
- в двухмерном потоке — two-dimensional flow test
-, вибрационное — vibration test
- в полете — flight test, inflight test
- в свободной атмосфере — free-air test
- в свободном полете — free flight test
- в трехмерном потоке — three-dimensional flow test
-, выборочное (с отбором определенного количества образцов) — percent test
-, выборочное (с произвопьным отбором образцов) — random test, sampling test
-, высотное — altitude test
- гермокабины на герметичность — pressurized cabin leakage test
-, государственное — official test
- давлением — pressure test
- двигателя — engine test
-, длительное (двигателя) — endurance test
-, длительное поэтапное (двигатепя) — endurance block test
-, заводское — factory test
-, заводское летное (опытного ла) — prototype factory flight test
-, заводское летное (серийного ла) — production flight test
-, зачетное — proof-of-compliance test
- знакопеременными нагрузками — alternate-stress test
- изоляции, высоковольтное — high-voltage test
проверка качества изоляции эп. оборудования под током высокого напряжения. — а test of insulation charaeteristics of electrical equipment performed at a specified test voltage.
-, климатическое — environmental test
-, комиссионное — qualification test
-, контрольное — check test
-, контрольное (двигателя) — calibration test
испытание для определения мощноетных характеристик и условий длительных испытаний. — то establish the engine power characteristics and the conditions for the endurance test.
-, контрольное (для подтверждения правильности сборки двигателя после ремонта) — final test. the test is conducted to ascertain that overhauled engine is assembled correctly.
-, копровое (шасси) — drop test
-, летное — flight test
- на влажность — humidity test
- на воздействие вибраций — vibration test
- на воздействие высоких температур — high temperature test
- на воздействие низких температур — low temperature test
- на воздействие морского тумана — salt spray test
- на воздействие пыли — sand and dust test
- на воздействие ускорений — acceleration test
- на воздействие окружающей среды — environmental test
- на выносливость — fatigue test
- на герметичность — leak test
- на герметичность (при создании разрежения внутри объекта) — vacuum retention test
-, нагрузочное (эл. оборудования) — proof test test of equipment with load conditions outside the normal.
-, наземное — ground test
- на излом — fracture test
- на износ — wear test
- на истирание — abrasion test
- на кручение — torsion test
- на перегрузку от ускорений — acceleration test
- на привязи (вертолета) — tie-down test
- на пробой изоляции — insulation breakdown test
при испытании на пробой (электрическую прочность) изоляция должна выдерживать напряжение 500 в (50 гц) переменного тока, подаваемаго на любую пару контактов. — at insulation breakdown test application of 500 v, 50 hz ас across any terminals must cause no electrical breakdown of the insulation.
- на продолжительность работы — endurance test
- на прочность — structural test
- на работоспособность — operational /operation/ test
испытание для установления того, что система или агрегат выполняют свои функции. — that procedure required to ascertain only that а system or unit is operable.
- на работоспособность (амортизатора шасси) — (shock strut) reverse energy absorbtion capacity test
- на разрыв — tensile test
- на (амортизационный) ресурс — service life test
- на соответствие (характеристикам) ту — functional test
испытание дпя установления того, что рабочие параметры системы или агрегата находятся в пределах, оговоренных техническими условиями. — that procedure required to ascertain that а system or unit is functioning in all aspects in accordance with minimum acceptable system or unit design specifications.
- на тепловой удар — thermal shock test
- на ударную прочность — shock test
- на усталостное разрушение — fatigue test
- на утечку мыльной пеной — leak-test with soap suds aрplied coat the pipe with soap suds to detect leakage.
- на флаттер — flutter test
- на экстремальные нагрузки — proof tesi
a test of an equipment with load conditions outside the normal, but which may occur.
-, огневое (на воздействие пламени) — flame test
- отдельных узлов двигателя (стендовое) — engine component test
- по определению нагрузок, действующих на агрегаты в полете — flight stress measurement test
-, поверочное — chsck test
-, полномасштабное — full-scale twst
- приемистости двигателя — engine acceleratian test
-, приемо-сдаточное (серийной техники) — acceptance test
-, приемо-сдаточное (несерийнон техники) — approval test
-, приемочное — acceptance test
- работспособности (энергоемкости) амортизации (шасси) — shock absorption test
-, ресурсное (двигателя) — engine service life test
-, рулежное — taxi test
-, самолета — airplane test
-, сдаточное — acceptance test
-, сертификационное — certification test
- системы охлаждения (силовой установки) — cooling test
-, статическое испытание самолета или его элементов на прочность под статической нагрузкой. — static test
-, стендовое — bench test
-, ударное — impact test
-, усталостное — fatigue test if substantiation of the pressure cabin by fatigue tests is required, the cabin must be cycle-pressure tested.
-, функциональное — operational /operation/ test
испытание для проверки работоспособности системы или агрегата, — the proper functioning of the retracting mechanism must be shown by operation tests.
-, циклическое (проводимое циклами) — cycle test
- шасси на копре, динамическис — landing gear drop test
данные и. — test data
"идут и." (надпись) — test in progress
отчет об и. — test report
последовательность и. — testing sequence
проведение и. — conduct of test
продолжитепьность и. — duration of test
результаты и. — test results
условия и. — test conditions
подвергать и. — subject to test
подлежать и. — be subject to test
подтверждать испытанием проводить и. — substantiate by test conduct test
проводить и. в полете — test in flight
проводить летное и. — conduct flight test
проводить и. на... — perform test on...
(оборудовании, стенде, макете и т.п.) — the tests must be performed on a mock-up using the same equipment used in the airplane.
проводить и. на самолете — conduct test on aircraft
проходить и. — undergo test
двигатель должен проходить вибрационные испытания для исследования его вибрационных характеристик. — each engine must undergo a vibration test to investigate the vibration characteristics.
проходить и. в полете — be tested in flight, be flight tested
проходить заводское и. — be factory tested
проходить летное и. — be tested in flight, be flight testedРусско-английский сборник авиационно-технических терминов > испытание
-
7 проверка
check, checkout, testпроверка внешнего вида и фактического состояния оборудования — check of the equipment for the appearance and apparent conditionпроверка выборочная — selection check, selective check, spot check, check at randomпроверка герметичности — leakage test, leak test▪ As you become more familiar with the equipment, you will learn of additional inspection points and their importance as part of the overall system checkout.▪ Items must pass the prescribed cleanliness test.проверка повторная — check inspection, reinspection▪ Provide enough clearance in the rear of the cabinets for removal of the rear cover during maintenance checks. Make frequent preventive maintenance checks of the radio set. Pay particular attention to the lubrication of the equipment.проверка работы (работоспособности) — functional checkout, functional test▪ Checkout is a sequence of functional, operational and calibrational tests to determine the condition and status of a weapon system or element thereof.▪ Technical inspection: 1. Inspection of equipment or weapons to determine whether they are serviceable for continued use or whether repairs are necessary. 2. The initial, in-process, and final inspections performed within a maintenance unit or materiel, incident to repair, to determine condition, deficiencies, parts requirements, nature of repairs necessary, and whether the item will be repaired locally, salvaged, or evacuated (initial inspection); to determine whether repair in process are being performed properly (in-process inspection); and to determine, before disposition is made of a repaired item, whether all required repairs were performed satisfactorily [final inspection].проверка регулировка и испытание после ремонта — postrepair checks, adjustments and testsПоставки машин и оборудования. Русско-английский словарь > проверка
-
8 проверка
check (снк), test, inspection
- (раздел рэ) — adjustment/test
-, автономная (инерц. сист.) — self-testing
-, безвыборочная — random check
- биения (радиального) — check for /of/ eccentricity
- биения (скоса боковой поверхности, напр., колеса турбины) — check of swash. checking the swash of turbine wheel.
- введенных координат гпм — waypoint coordinate insertion /entry/ verification
- включения (работы) системы — system operational test
-, внерегламентная — unschedule maintenance check
проверки или осмотры самолета, его систем и агрегатов, проводимые в результате нарушения нормальных условий эксплуатации, независимо от утвержденных сроков проверок, производятся после грубых посадок, в случае удара молний в самолет, посадки с избыточным весом, столкновения с птицей и др. — those maintenance checks and inspection on the aircraft, its systems and units which are dictated by special or unusual conditions which are not related to the time limits. includes inspections and checks such as hard landing, turbulent air, lightning strike, overweight landing, bird strike
- встроенным контролем — built-in test
test the system by using its built-in test facility /ieature/.
-, выборочная — spot check, sampling inspection
-, выборочная (на работоспособность) — spot test
- гермокабины на герметичность — pressurized cabin leakage test
- готовности (ла) к полету — pre-flight check
"- заправки топливом" — fuel oty test (switch) (выключатель)
-, комплексная (систем) — combined systems checkout
-, контрольная — inspection check
- концентричности (колеса турбины, вала) — check of concentricity (of turbine wheel, shaft)
- координат места ла — aircraft position coordinate verification
- ламп — lamp test
- ламп табло (повторным включением) — annunciator lights recall. any reset annunciator lights can be recalled using the warning, caution and advisory lights test switch.
- межпопетная (перед обратным маршрутом) — turnround check
- методом "прокачек" (функциональная проверка электр. цепей) — functional test
- на выявление трещин (одним из объективных методов дефектоскопии) — inspection for cracks (by emplaying an objective method of inspection)
- на герметичность — leak test
-, наземная — ground check
-, наземная (с опробованием) — ground test
- на нспопнитепьном старте — lne-up check
- на магнитном дефектоскопе (на выявление трещин) — magnetic inspection (for cracks)
- на месте (без демонтажа изделия или агрегата с объекта) — in-situ check /test, inspection/. the on-condition check is normally an in-situ test.
- на оправке — check on mandrel
- на правильность формы и взаимного расположения поверхностей (детали) — test for truth
сюда относятся проверки на (не)плоскостность, (не)перпендикулярность, (не)параллельность, овальность и на правильность совмещения отверстий. — the methods for testing for form and alignment are used to check the flatness, squareness, angular relationship or parallelism of the part surfaces, the alignment of holes or the true circularity of round parts.
- на пробой изоляции — insulation breakdown test
- на работоспособность (для подтверждения нормальной работы изделия) — operational test. the procedure required to ascertain only that a system or unit is operable.
- на работоспособность (для подтверждения эксплуатационных характеристик) — operation test. то demonstrate the engine operational characteristics.
- (реакции двигателя) на сброс газа — deceleration test
- на слух — listening test
перебои в работе двигателя могут определяться проверкой на слух, — listening test is employed to determine the engine rough operation.
- на соответствие техническим условиям — functional test
проверка, проводимая с целью подтверждения, что система или агрегат работает в соответствии с минимально допустимыми ту. — the procedure required to ascertain that а system or unit is functioning in all aspects in accordance with minimum acceptable design specifications.
- на стоянке — ramp check /test, inspection/
simple test module provides rapid ramp check.
- на утечку (герметичность) — leak-test
- на утечку мыльной пеной — leak-test with soap suds арplied
coat the pipe with soap suds to detect leakage.
- наличия электрической цепи от...до... — check of electrical circuit between...and...for continuity
- нивелировки (заклинения) неподвижных поверхностей самолета — check of rigging of fixed surfaces
- огнетушителей (без разряда) — fire extinguisher test (firex
нажать кнопку проверка огнетушителей и в этом случае должны загораться лампы 1-я очередь и 2-я очередь срабатывания. — press the firex test button and all main and altn lights illuminate on fire extinguisher test panel.
-, перекрестная (напр., всех аналогичных приборов) — crosscheck (хснеск) crosscheck the three altimeters.
-, периодическая — periodic check
- пиропатронов (противопожарной системы) — squib test. repeat procedure with squib test switch in aft position.
- плоскостности детали на контрольной плите — check for flatness of a part surface against the face of a surface plate
для проведения данной проверки на поверхность кантрольной плиты наносится краска (берлинская лазурь), затем чистая проверяемая поверхность прижимается к контрольной плите. плоскостность проверяемой поверхности, оценивается no наличию отпечатков краски (на выступающих участках). — то make the test, smear the face of the surface plate with marking (consisting of prussian blue or redlead with oil), then wipe clean the sruface to be checked and rub it lightly on the surface plate. the truth of the surface can be estimated by the appearance of the transferred marking.
-, повторная — recheck
- под током /напряжением/ (оборудования, системы) — test /check/ of equipment energized, alive (equipment) test
- по налету — check by flight hour(s)
-по налету, регламентная — periodic /scheduled/ maintenance cheek by flight hour(s)
-, послемонтажная — post-installation check
-, послеполетная — post-flight check
- по состоянию (по мере надобности) — оn-condition check (ос)
профилактическое техническое обслуживание (контроль качества ремонта), выполняемое в виде периодических осмотров, проверок (или испытаний изделия (агрегата), на обнаружение механических дефектов (в доступных пределах) для определения допустимости дальнейшей эксппуатации изделия (до следующей проверки по состоянию). — а failure preventive primary maintenance (overhaul control) process which requires that the item be periodically inspected, checked or tested against some appropriate physical standards (wear or deterioration limits) to determine whether the item can continue its service (for another ос check interval).
- по техническому состоянию — оn-condition check
- по форме "а" ("в", "с"), регламентная (периодиче — scheduled (periodic) "а" ("в", "с") check
- правильности ввода данных — data entry /insertion/ verification
-, предварительная — preliminary check
-, предвзлетная (по контрольной карте) — pre-takeoff check, before-takeoff check
-, предполетная — pre-flight check
-, предпосадочная (по контрольной карте) — pre-landing check, beforelanding check
-, предстартовая — prestart procedure
- приемистости (двигателя) — acceleration test
- прилегания поверхностей на краску (берлинскую лазурь) — check of the surfaces for close contacting indicated by continuity of (prussian blue) marking transferred
-, принудительная (вводимая вручную) — manually initiated /induced/ test /check/
- противообледенительной системы (надпись) — anti-ice test
- противопожарной системы (надпись) — firex test
- работоспособности — operational test
- работы — operational test
- радиального биения (рабочего колеса турбины (на оправке) — check of eccentricity /concentricity/ of turbine wheel (on mandrel)
-, регламентная — scheduled maintenance check
проверки самолета, его систем и агрегатов в указанные сроки. — those manufacturer recommended check and inspections of the aircraft, its systems and units dictated by the time limits.
- самолетов парка, выборочная — sampling inspection of fleet
"- сигнальных ламп" (надпись) — lamp test
- системы — system test (sys tst)
- системы сигнализации пожаpa — fire warning) test
"- системы сигн. пож. в otc. дв. (надпись) — eng compt fire warn test
-, совместная (проводимая поставщиком и покупателем) — conjoint check, check or test conjointly conducted (by supplier and buyer)
- соконусности несущего винта (вертолета) — rotor blade tracking test
- сопротивления изоляции — insulation-resistance test
test for measuring ohmic resistance of insulation.
- с помощью встроенного контроля — built-in test
- с (к-л.) пульта (или наборного поля) — test /check/ via /from/ сапtrol panel (or keyboard)
-, стартовая — on line test
-, стендовая — bench test
-, стендовая (испытание) — bench check/test/
- технического состояния — operational status check, check for condition
-, транзитная — transit check
план транзитного полета включает транзитную проверку. — the transit time schedule includes transit check.
-, тщательная — thorough check
-, функциональная — functional test
- электрической прочности (изоляции) — (insulation) voltage-withstand test
проверка способности изоляции выдерживать (повышеннoe против нормы) напряжение. — application of voltage (higher than rated) for determining the adequancy of insulation materials against breakdown.
- элементов конструкции (ла), выборочная — structural sampling test
- эффективности системы охлаждения (двигателя и редуктора вертолета) при взлете (висении, наборе высоты, снижении) — takeoff (hovering, climb, descent) cooling test
'включение проверки' (надпись) — test on
причина п. — reason for check /test/
производить п. по 3, пп. a,6 — test the unit according to requirements of para. 3 (a, b)Русско-английский сборник авиационно-технических терминов > проверка
-
9 схема
(см. также схемы радиоэлектронного оборудования)diagram, chartсхема подключения при испытаниях — test(ing) set-up, test setupсхема принципиальная (заголовок в -тех. описании) — schematic diagram analysis (of transmitter, etc.)схема последовательности операций (при обслуживании, ремонте) — flowsheetсхема проверки (проведения испытания) — test(ing) set-up, test setupСобрать схему проверки как показано на рисунке 5 — Set up the test equipment as shown in Fig. 5схема работы номеров расчета при развертывании, подготовке к работе и т.д. — systematic procedure for emplacement of equipment, etc.▪ This manual describes systematic procedures for preparation for operation or travel of the missile system, the drills for operation of the equipment, and the emergency operating procedures.схема расположения оборудования (в прицепе, фургоне, кабине и т.д.) — equipment layout (in trailer, van, shelter, etc.)схема структурная (блок-схема, заголовок в тех. описании) — block diagram analysis (of transmitter, etc.)схема технологическая — flowsheet, process sheet, route sheetсхема укладки — packing diagram, stowage diagramсхема функциональная (заголовок в тех. описании) — functional diagram analysis (of modulator, etc.)————————схема монтажная (схема соединений - показывает электрические соединения составных частей изделия, марку провода, жгута и кабеля, которыми эти соединения осуществляются, а также места их ввода зажимы, разъемы и т.д.) — wiring diagram, internal connection diagramсхема общая (определяет составные части комплекса и соединение их между собой на месте эксплуатации) — system diagramсхема принципиальная (полная - определяет полный состав элементов и связей между ними) — schematic diagram, elementary diagramсхема расположения (определяет относительное расположение составных частей изделия) — layout diagramсхема структурная (определяет основные функциональные части изделия, их назначение и взаимосвязь) — block diagramсхема функциональная (разъясняет определенные процессы, протекающие в функциональных цепях изделия или изделий в целом) — functional diagram, signal flow diagramПоставки машин и оборудования. Русско-английский словарь > схема
-
10 схема
diagram
(графическое изображение соединений и функциональных зависимостей в системе)
- (система) — system
- (электрическая или эпектронная сеть) — circuitry
- аварийного покидания самолета в воздухе (пути покидания ла) — bailout escape routes
- аварийного покидания ла на земле (пути покидания ла) — evacuation routes
-, аэродинамическая — aerodynamic configuration
- взлета (рис. 112) — takeoff pattern
- в трех проекциях (рис. 130) — three-view outline drawing
- газовоздушного тракта двигателя (рис. 47) — engine gas flow
-, двухтактная (усилителя) — push-pull circuit
а push-pull three-stage amplifier.
- действия — functional diagram
- деления самолета на зоны — zoning diagram
- деления самолета на зоны с указанием эксплуатационных лючков — aircraft zoning diagram and асcess door and panel identification
- дистанций (рис. 131) — station diagram
- захода на посадку (рис. 115) — landing /approach/ pattern
- "и" (в вычислительном устройстве) — and circuit, and gate (circuit)
in an electronic computer, a gate circuit with more than one control (input) terminal.
-, интегральная — integrated circuit
цепь собрана на интегральных схемах. — а system uses /based on use of/ integrated circuits.
-, кинематическая — functional diagram
-, кинематическая (заголовок раздела руководства) — mechanical description
- локализация отказов — fault isolation diagram
-, мнемоническая (топливной системы) — (fuel system) mnemonic diagram
-, монолитная (эл.) — solid-state circuitry
all solid-state circuitry is used in many key chassis areas.
-, монтажная (эл.) — wiring diagram
электромонтажная схема, показывающая расположение и содержащая обозначения элементов и соединительных проводников блока или цепи. — the wiring diagram shall be an installation drawing showing and identifying the units and conductors that make up the installation.
- нагружения (элементов системы управления рулем высоты) — (elevator control system) loading conditions
- обратной связи — feedback circuit
- организации технологического процесса ремонта (карта) — overhaul flow (chart)
- основных технологических разъемов — production breakdown diagram
- отыскания и устранения неисправностей — trouble shooting chart
-, печатная (плата) — printed circuit (board)
- поиска неисправностей (карта) — trouble shooting card
- (маршрут) полета в зоне ожидания (на малой высоте) — (low altitude) holding pattern. the economical engines permit the aircraft to fly in the low altitude holding pattern.
- (маршрут) полета в зоне ожидания на экономическом режиме. — economic holding pattern. reduced fuel consumption is obtained by flying in economic holding pattern.
- (профиль) полета — flight profile
-, полумонтажная (в афс) — wiring diagram
- последовательности работы (агрегатов) — sequence-of-operation diagram
- приводов агрегатов, кинематическая — accessory drives gear train (diagram)
-, принципиальная (графическое изображение) — schematic diagram
схема наглядно иллюстрирует взаимодействие элементов сложных систем (цепей) и облегчает отыскание и устранение неисправностей в этих системах. элементы изображаются условными графическими обозначениями. — the schematic diagram facilifates tracing and trouble shooting complex circuits. it shows by means of graphic symbols all the components required to perform system operation.
-, принципиальная электрическая (заголовок раздела ру ководства) — electrical description
-, принципиальная упрощенная — simplified schematic diagram
- проверки, поверочная (схема соединений поверочного оборудования) — test set up /setup/ (diagram)
- работы (графическое изображение) — functional diagram
- работы (принцип действия, заголовок раздела) — operation
- разворота (самолета на земле) — turning circle
- размещения и швартовки грузов (в грузовой кабине) — cargo arrangement and lashing /tie-down/ diagram
- расположения агрегатов — arrangement diagram
- ремонта, технологическая (карта) — overhaul flow chart
- соединений — connection diagram
- соединений (полумонтажная в афс) — wiring diagram
- соединений поверочной установки (подрисуночная надпись бпок-схемы) — test equipment setup (diagram)
-, структурная (блок-схема) — block diagram
- технологических разъемов (изображение в расчлененном виде) (рис. 1) — exploded view drawing (showing major components of airplane)
- технологичесмих разъемов (групп) самолета — aircraft major components exploded view (diagram)
- технологического процесса ремонта (изделия) — overhaul procedures. overhaul procedures include cleaning, disassembly, etc.
- трубопроводов — piping diagram
·-, упрощенная — simplified diagram
-, упрощенная принципиальная — simplified schematic diagram
- установки (агрегата) — installation diagram
- "утка" (о самолете) — canard configuration
- фазовой автоподстройки частоты (фапч) — phase-locked loop (pll)
-, фидерная (эл.) — wiring diagram
-, функциональная (блок-схема) — block diagram
-, цветовая — color scheme
цветовая схема салона выполнена в зеленоватых и кремовых тонах. — color scheme of the passenger cabin is of green and cream.
-, центровочная (заголовок) (рис. 132) — (airplane) center of gravity (cg) limits
- членения (самолета или агрегата) (рис. 1) — exploded view drawing
- шасси — landing gear configuration
- шасси, трехопорная (с передней опорой) — tricycle landing gear
- шасси, трехопорная (с хвостовым колесом) — tail wheel(-type) landing gear
- швартовки грузов (в грузовой кабине) — cargo lashing /tie-down/ diagram
- швартовки техники (колесной и гусеничной) (в грузовой кабине) — vehicle lashing /tie-down/ diagram
- шпангоутов (дистанций) фюзеляжа (для определения координат цт) — station diagram
-, электрическая (графическое изображение) — electrical diagram
-, электрическая (заголовок раздела руководства) — electrical description
-, электрическая (система) — electrical system
-, электрическая (совокупность электрических цепей) — (electrical) circuitry
-, электромонтажная — wiring diagram
альбом фидерных с. — wiring diagram manual
блок-с. — block diagram
порядок сборки поверочной с. — test set-up procedure
быть выполненным (реализованным, собранным) по с. — be built on /around/ (circuit), be based on /using, employing/ circuit
the rectifier is built on a bridge circuit.
доработка с. (эл. цепей) — circuit modification
доработка с. (внесение изменений в эл. схемы в руководстве, инструкции) — revision to (wiring) diagram
собирать по с. — build (smth) on /around/ as...
connect amplifier as a differential circuit.
собирать схему проверки — connect equipment in setupРусско-английский сборник авиационно-технических терминов > схема
-
11 контроль
inspection, testing method
(дефектоскопия)
- (наблюдение, слежение за параметрами, показаниями) — monitoring
- (наблюдение за соблюдением правил) — supervision
- (осмотр) — inspection
- (проверка) — check (сhk)
- (проверка на работоспособность) — test (tst) press the lamp test or sys tst button.
"-" (табло проверки работоспособности системы) — monitor (annunciator) pressing test-1 switch displays all monitor annunciators
- (функция регупирования или управления) — control, monitoring
- ведения формуляра (раздел формуляра) — log book entries check
-, встроенный — built-in test facility /feature/, integral test facility /feature/
встроенный контроль служит для проверки системы в полете и быстрого определения неисправностей. — built-in test facilities are provided for inflight system check and rapid fault diagnosis on the aircraft.
-, встроенный (аппаратура) — built-in test equipment (bite)
-, встроенный (цепи контроля) — built-in test circuits
- встроенный (цепи сигнализации неисправностей) — malfunction warning circuits (system)
-, входной (комплектующих изделий перед установкой) — functional test
-, входной (при приемке в ремонт) — (accept-to-overhaul) inspection/check
-, допусковый — tolerance cheek
- и коррекция координат мс при пролете станции вор — position check/update overhead а vor station
- исправности — integrity monitoring /check/
- качества в процессе серийного производства — production inspection the methods used for production inspection of individual parts and complete assemblies.
-, капиллярный — liquid penetrant inspection
-, комплексный (систем) — combined systems checkout
-, люминисцентный (люма, дефектоскопия) — fluorescent inspection
-, магнито-порошковый — magnetic (particle) inspection
-, магнитный — magnetic inspection
-, междуполетный (межполетный) — turnround check /inspection/
- методом вихревых токов — eddy current inspection
- методом красок (цветной) — dye penetrant inspection
- нагрузки шины (no.i) paдиооборудования — radio bus (1,no. i) load monitor(ing)
- надежности (работы агрегата системы) — reliability test
- надежности (сигнала) — reasonability test
- напряжения — voltage monitoring
-, неразрушающий — nоn-destructive inspection
- no мере необходимости — condition-monitoring (cm)
при данном контроле не требуется никаких периодических осмотров для опредепсния срока службы или необходимости замены, или ремонта изделия до его отказа. — no maintenance task is required to evaluate life expectancy or replace the item for overhaul, before it fails.
- по состоянию (см. обслуживанне) — on-condition inspection /check, test/
- по состоянию, периодический — regularly scheduled on-condition check
-, полетный (оборудование) "- ппc" (надпись) — flight test (equipment) firex test
-, предполетный (работы системы) — pre-flight test
- работы — function monitoring /test/
"-работы" (переключатель) — test
"- работы двигателей" (общий трафарет пульта бортинженера) — engines
- работы радиостанции самоподслушиванием — side-tone monitoring
- работы системы (перечень указателей и сигнальных устройств) — indicators
"- работы системы" (переключатель) — system test (sys tst)
- расхода топлива — fuel consumption check
-, рентгеноскопический — х-ray inspection
- системы — system test (sys tst)
- состояния — condition-monitoring (cm)
cm is a maintenance concept that relics on surveillance and evaluation of airplane, system and/or component performance.
- состояния системы — system status monitoring
- тока — load monitoring
"-тока" (надпись у амперметра) — load monitor(ing)
-, ультразвуковой (узк) — ultrasonic inspection
- функционирования, встроенный — built-in test
- функционирования и сигнализации выхода из строя, встроенный — built-in test and malfunction warning circuit
-, цветной — dye penetrant inspection
- частоты — frequency monitoring
-, электромагнитный — electro-magnetic inspection
предъявпять на к. (после ремонта) — assert for inspection clearance
устанавливать по (после) предъявлению на к. — install on /after/ inspection clearanceРусско-английский сборник авиационно-технических терминов > контроль
-
12 заводские приемочные испытания системы автоматизации подстанции
заводские приемочные испытания системы автоматизации подстанции
Согласованные заказчиком функциональные испытания изготовленной на заказ системы автоматизации подстанции или ее частей с использованием набора параметров, предназначенных для применения на подстанции.
Примечание. Эти испытания следует проводить на площадке изготовителя или системного интегратора с использованием испытательного оборудования, имитирующего производственный процесс.
[ ГОСТ Р 54325-2011 (IEC/TS 61850-2:2003)]
заводские приемочные испытания
-
[ ГОСТ Р 54325-2011 (IEC/TS 61850-2:2003)]EN
factory acceptance test
customer agreed functional tests of the specifically manufactured SAS installation or its parts, using the parameter set for the planned application. This test should be carried out in the factory of the system integrator by use of process simulating test equipment
[IEC 61850-2, ed. 1.0 (2003-08)]Тематики
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > заводские приемочные испытания системы автоматизации подстанции
-
13 опытный образец
1) General subject: development type, developmental prototype2) Naval: experimental prototype3) Military: Y (ЛА), development prototype, pilot item, testbed (англ. термин взят из репортажа агентства Thomson Reuters; контекстуальный перевод)4) Engineering: engineering sample, experimental model, pilot model, preproduction model, prototype, prototype machine, prototype model, prototype preproduction model, prototype unit, test sample5) Agriculture: check sample, control sample, proof sample6) Economy: first article, pilot sample, test pattern7) Accounting: prototype model (напр. машины)8) Automobile industry: trial model9) Electronics: test model10) Information technology: trial design11) Oil: test piece, test specimen12) Astronautics: functional equipment, predictable pattern13) Advertising: pilot sample (изделия)14) Business: certificate model15) EBRD: industrial prototype16) Automation: R and D model, engineering prototype, preproduction prototype, production prototype, prototype sample18) Chemical weapons: test prototype -
14 выдвижная часть
выдвижная часть
Съемная часть, которая может быть перемещена из присоединенного положения либо в отсоединенное положение, либо в испытательное положение, оставаясь механически соединенной с НКУ.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
выдвижная неотделяемая часть
Часть СНКУ, которая может быть либо отсоединена от него, либо установлена в испытательное положение, оставаясь механически соединенной с СНКУ.
[ ГОСТ Р МЭК 61439.2-2012]EN
withdrawable part (of an assembly)
a removable part of an assembly that can be moved to one or more positions in which an isolating distance or a segregation between open contacts is established while the part remains mechanically attached to the assembly
NOTE – The isolating distance or the segregation always relates to the main circuit. It may or may not refer to the auxiliary circuits or to control circuits.
[IEV number 441-13-09]
withdrawable part
removable part intended to be moved from the connected position to the isolated position and to a test position, if any, whilst remaining mechanically attached to the PSC-assembly
[IEC 61439-2, ed. 2.0 (2011-08)]FR
partie débrochable (d'un ensemble)
partie amovible d'un ensemble qui, tout en demeurant reliée mécaniquement à l'ensemble peut être déplacée jusqu'à la ou l'une des positions établissant une distance de sectionnement ou un cloisonnement métallique entre contacts ouverts
NOTE – Cette distance de sectionnement ou ce cloisonnement métallique concerne toujours le circuit principal. Elle peut concerner ou non les circuits auxiliaires ou les circuits de commande.
[IEV number 441-13-09]
partie débrochable
partie amovible prévue pour être déplacée de la position raccordée à la position de sectionnement et à une éventuelle position d'essai tout en restant mécaniquement reliée à l'ensemble EAP
[IEC 61439-2, ed. 2.0 (2011-08)]
7.6.4.2 Блокировка и замки для выдвижных частей
Как правило, выдвижные части должны иметь устройство, гарантирующее передвижение их в разные положения только после отключения главной цепи.
Для предотвращения недозволенных операций выдвижные части должны иметь замки или запоры, фиксирующие их в одном или более положениях.
[ ГОСТ 22789-94( МЭК 439-1-85)]
Рис. Schneider Electric Параллельные тексты EN-RUThe modularity of the Blokset functional switchboards means you can modify or upgrade them with ease to adapt to your changing processes.
The withdrawable drawers let you make these upgrades while the equipment is energised, without cutting switchboard supply and in complete safety. The withdrawable drawers have 3 positions: connected, disconnected and safe testing.
[Schneider Electric]НКУ Blokset имеет модульную конструкцию, что позволяет в случае изменения технологического процесса легко изменять или модернизировать такое НКУ.
Выдвижные ящики позволяют проводить совершенно безопасно модернизацию НКУ без отключения питания НКУ и электроустановки. Выдвижные ящики имеют три положения: присоединенное, отсоединенное и безопасное испытательное.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > выдвижная часть
15 выдвижная часть
выдвижная часть
Съемная часть, которая может быть перемещена из присоединенного положения либо в отсоединенное положение, либо в испытательное положение, оставаясь механически соединенной с НКУ.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
выдвижная неотделяемая часть
Часть СНКУ, которая может быть либо отсоединена от него, либо установлена в испытательное положение, оставаясь механически соединенной с СНКУ.
[ ГОСТ Р МЭК 61439.2-2012]EN
withdrawable part (of an assembly)
a removable part of an assembly that can be moved to one or more positions in which an isolating distance or a segregation between open contacts is established while the part remains mechanically attached to the assembly
NOTE – The isolating distance or the segregation always relates to the main circuit. It may or may not refer to the auxiliary circuits or to control circuits.
[IEV number 441-13-09]
withdrawable part
removable part intended to be moved from the connected position to the isolated position and to a test position, if any, whilst remaining mechanically attached to the PSC-assembly
[IEC 61439-2, ed. 2.0 (2011-08)]FR
partie débrochable (d'un ensemble)
partie amovible d'un ensemble qui, tout en demeurant reliée mécaniquement à l'ensemble peut être déplacée jusqu'à la ou l'une des positions établissant une distance de sectionnement ou un cloisonnement métallique entre contacts ouverts
NOTE – Cette distance de sectionnement ou ce cloisonnement métallique concerne toujours le circuit principal. Elle peut concerner ou non les circuits auxiliaires ou les circuits de commande.
[IEV number 441-13-09]
partie débrochable
partie amovible prévue pour être déplacée de la position raccordée à la position de sectionnement et à une éventuelle position d'essai tout en restant mécaniquement reliée à l'ensemble EAP
[IEC 61439-2, ed. 2.0 (2011-08)]
7.6.4.2 Блокировка и замки для выдвижных частей
Как правило, выдвижные части должны иметь устройство, гарантирующее передвижение их в разные положения только после отключения главной цепи.
Для предотвращения недозволенных операций выдвижные части должны иметь замки или запоры, фиксирующие их в одном или более положениях.
[ ГОСТ 22789-94( МЭК 439-1-85)]
Рис. Schneider Electric Параллельные тексты EN-RUThe modularity of the Blokset functional switchboards means you can modify or upgrade them with ease to adapt to your changing processes.
The withdrawable drawers let you make these upgrades while the equipment is energised, without cutting switchboard supply and in complete safety. The withdrawable drawers have 3 positions: connected, disconnected and safe testing.
[Schneider Electric]НКУ Blokset имеет модульную конструкцию, что позволяет в случае изменения технологического процесса легко изменять или модернизировать такое НКУ.
Выдвижные ящики позволяют проводить совершенно безопасно модернизацию НКУ без отключения питания НКУ и электроустановки. Выдвижные ящики имеют три положения: присоединенное, отсоединенное и безопасное испытательное.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Синонимы
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > выдвижная часть
16 выдвижная часть
выдвижная часть
Съемная часть, которая может быть перемещена из присоединенного положения либо в отсоединенное положение, либо в испытательное положение, оставаясь механически соединенной с НКУ.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
выдвижная неотделяемая часть
Часть СНКУ, которая может быть либо отсоединена от него, либо установлена в испытательное положение, оставаясь механически соединенной с СНКУ.
[ ГОСТ Р МЭК 61439.2-2012]EN
withdrawable part (of an assembly)
a removable part of an assembly that can be moved to one or more positions in which an isolating distance or a segregation between open contacts is established while the part remains mechanically attached to the assembly
NOTE – The isolating distance or the segregation always relates to the main circuit. It may or may not refer to the auxiliary circuits or to control circuits.
[IEV number 441-13-09]
withdrawable part
removable part intended to be moved from the connected position to the isolated position and to a test position, if any, whilst remaining mechanically attached to the PSC-assembly
[IEC 61439-2, ed. 2.0 (2011-08)]FR
partie débrochable (d'un ensemble)
partie amovible d'un ensemble qui, tout en demeurant reliée mécaniquement à l'ensemble peut être déplacée jusqu'à la ou l'une des positions établissant une distance de sectionnement ou un cloisonnement métallique entre contacts ouverts
NOTE – Cette distance de sectionnement ou ce cloisonnement métallique concerne toujours le circuit principal. Elle peut concerner ou non les circuits auxiliaires ou les circuits de commande.
[IEV number 441-13-09]
partie débrochable
partie amovible prévue pour être déplacée de la position raccordée à la position de sectionnement et à une éventuelle position d'essai tout en restant mécaniquement reliée à l'ensemble EAP
[IEC 61439-2, ed. 2.0 (2011-08)]
7.6.4.2 Блокировка и замки для выдвижных частей
Как правило, выдвижные части должны иметь устройство, гарантирующее передвижение их в разные положения только после отключения главной цепи.
Для предотвращения недозволенных операций выдвижные части должны иметь замки или запоры, фиксирующие их в одном или более положениях.
[ ГОСТ 22789-94( МЭК 439-1-85)]
Рис. Schneider Electric Параллельные тексты EN-RUThe modularity of the Blokset functional switchboards means you can modify or upgrade them with ease to adapt to your changing processes.
The withdrawable drawers let you make these upgrades while the equipment is energised, without cutting switchboard supply and in complete safety. The withdrawable drawers have 3 positions: connected, disconnected and safe testing.
[Schneider Electric]НКУ Blokset имеет модульную конструкцию, что позволяет в случае изменения технологического процесса легко изменять или модернизировать такое НКУ.
Выдвижные ящики позволяют проводить совершенно безопасно модернизацию НКУ без отключения питания НКУ и электроустановки. Выдвижные ящики имеют три положения: присоединенное, отсоединенное и безопасное испытательное.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выдвижная часть
См. также в других словарях:
functional test — A test carried out while a circuit or equipment is operating under normal working conditions … IT glossary of terms, acronyms and abbreviations
Test and tagging — is a generic name given to the process of visually inspecting and electrically testing in service electrical equipment for personal use and/or safety. Colloquially, it is also referred to as; tagging, test tag, test and tag, electrical tagging,… … Wikipedia
Test engineer — A (hardware) test engineer (TE) is a professional who determines how to create a process that would test a particular product in manufacturing, or related area like RMA department, in order to guarantee that the product will be shipped out with… … Wikipedia
Functional magnetic resonance imaging — Functional MRI or functional Magnetic Resonance Imaging (fMRI) is a type of specialized MRI scan. It measures the haemodynamic response related to neural activity in the brain or spinal cord of humans or other animals. It is one of the most… … Wikipedia
Design For Test — (aka Design for Testability or DFT ) is a name for design techniques that add certain testability features to a microelectronic hardware product design. The premise of the added features is that they make it easier to develop and apply… … Wikipedia
In-circuit test — (ICT) is an example of white box testing where an electrical probe tests a populated printed circuit board (PCB), checking for shorts, opens, resistance, capacitance, and other basic quantities which will show whether the assembly was correctly… … Wikipedia
Air Force Operational Test and Evaluation Center — Infobox Military Unit unit name= Air Force Operational Test and Evaluation Center caption= Air Force Operational Test and Evaluation Center emblem dates= 1 January 1974 country= United States allegiance= branch= United States Air Force type=… … Wikipedia
596 (nuclear test) — 596 is the codename of the People s Republic of China s first nuclear weapons test, detonated on October 161964 at the Lop Nur test site. It was a uranium 235 implosion fission device and had a yield of 22 kilotons. With the test, China became… … Wikipedia
Medical test — Intervention X ray of a hand. X rays are a common medical test. MeSH … Wikipedia
High test peroxide — HTP redirects here. For the internet transfer protocol, see Hypertext Transfer Protocol. For information on the House tree person test, see Psychological testing. For the amino acid, see 5 HTP.High test peroxide or HTP is a high (85 to 98… … Wikipedia
Design for testing — Design for Test (aka Design for Testability or DFT ) is a name for design techniques that add certain testability features to a microelectronic hardware product design. The premise of the added features is that they make it easier to develop and… … Wikipedia
Перевод: с русского на все языки
со всех языков на русский- Со всех языков на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский